revisions ltr description date (yr - mo - da) approved a changes in accordance with nor 5962 - r177 - 96. 96- 07- 10 m. a. frye b drawing updated to reflect current requirements. redrawn. - ro 05- 05- 02 r. monnin c update drawing as part of 5 year review. - jt 10- 10- 25 c. saffle current cage code 67268 the original first sheet of this drawing has been replaced . rev sheet rev sheet rev status rev c c c c c c c c of sheets sheet 1 2 3 4 5 6 7 8 pmic n/a prepared by donald r. osborne dla land and maritime columbus, ohio 43218 - 3990 http://www.dscc.dla.mil standard microcircuit drawing this drawing is available for use by all departments and agencies of the department of defense checked by d. a. dicenzo approved by n.a. hauck microcircuit, linear , low noise operational amplifier, monolithic silicon drawing approval date 87- 05- 27 amsc n/a revision level c size a cage code 14933 5962- 86887 sheet 1 of 8 dscc form 2233 apr 97 5962- e 007- 11
standard microcircuit drawing size a 5962- 86887 dla land and maritime columbus, ohio 43218 - 3990 revision level c sheet 2 dscc form 2234 apr 97 1. scope 1.1 scope . this drawing describes device requirements for mil - std - 883 compliant, non- jan class level b microcircuits in accordance with mil - prf - 38535, appendix a. 1.2 part or identifying number (pin) . the complete pin is as shown in the following example: 5962 - 86887 01 c a drawing number device type (see 1.2.1) case outline (see 1.2.2) lead finish (see 1.2.3) 1.2.1 device type(s) . the device type(s) identify the circuit function as follows: device type generic number circuit function 01 op - 227a dual, low - offset, low noise operational amplifier 1.2.2 case outline(s) . the case outline(s) are as designated in mil - std - 1835 and as follows: outline letter descriptive designator terminals package style c gdip1 - t14 or cdip2- t14 14 dual -in - line 1.2.3 lead finish . the lead finish is as specified in mil - prf - 38535, appendix a. 1.3 absolute maximum ratings . 1 / supply voltage (v cc ) ............................................................. 22 v dc input voltage range (v in ) ........................................................ 22 v dc output short circuit duration .................................................... indefinite differential input current .......................................................... 25 ma 2 / differential input voltage range ............................................... 0.7 v dc lead temperature (soldering, 60 seconds) ............................. +300 c storage temperature range ..................................................... -65 c to +150c maximum power dissipation (p d ) ........................................... 500 mw 3 / thermal resistance, junction -to - case ( jc ) ............................. see mil - std -1835 1.4 recommended operating conditions . supply voltage (v cc ) ............................................................. 4.5 v dc to 18 v dc ambient operating temperature range (t a ) ............................. -55 c to +125c ______ 1 / unless otherwise specified, all voltages are references to ground. 2 / the inputs are protected by back -to - back diodes. current limiting resistors are not used in order to achieve low noise. if differential input voltage exceeds 0.7 v, the input current should be limited to 25 ma. 3 / for t a greater than 106 c, derate l inearly at 11.3 mw/ c.
standard microcircuit drawing size a 5962- 86887 dla land and maritime columbus, ohio 43218 - 3990 revision level c sheet 3 dscc form 2234 apr 97 2. applicable documents 2.1 government specification, standards, and handbooks . the following specification, standards, and handbooks form a part of this drawing to the extent specified herein. unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. department of defense specification mil - prf -38535 - integrated circuits, manufacturing, general specification for. department of defense standards mil - std -883 - tes t method standard microcircuits. mil - std -1835 - interface standard electronic component case outlines. department of defense handbooks mil - hdbk -103 - list of standard microcircuit drawings. mil - hdbk -780 - standard microcircuit drawings. (copies of these documents are available online at http s ://assist.daps.dla.mil/quicksearch/ or from the standardization document order desk, 700 robbins avenue, building 4d, philadelphia, pa 19111 - 5094 .) 2.2 order of precedence . i n the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. requirements 3.1 item requirements . the individual item requirements shall be in accordance with mil - prf - 38535, appendix a for non - jan class level b devices and as specified herein. product built to this drawi ng that is produced by a qualified manufacturer listing (qml) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to mil - prf - 38535 may be processed as qml product in accordance with the manufacturers appro ved program plan and qualifying activity approval in accordance with mil - prf - 38535. this qml flow as documented in the quality management (qm) plan may make modifications to the requirements herein. these modifications shall not affect form, fit, or func tion of the device. these modifications shall not affect the pin as described herein. a "q" or "qml" certification mark in accordance with mil - prf - 38535 is required to identify when the qml flow option is used. 3.2 design, construction, and physical dimensions . the design, construction, and physical dimensions shall be as specified in mil - prf - 38535, appendix a and herein. 3.2.1 case outline . the case outline shall be in accordance with 1.2.2 herein. 3.2.2 terminal connections and logic diagram . the terminal connections and logic diagram shall be as specified on figure 1 . 3.3 electrical performance characteristics . unless otherwise specified herein, the electrical performance characteristics are as specified in table i and shall apply over the full ambient operating temperature range. 3.4 electrical test requirements . the electrical test requirements shall be the subgroups specified in table ii. the electrical tests for each subgroup are described in table i. 3.5 marking . marking shall be in accordance with mil - prf - 38535, appendix a. the part shall be marked with the pin listed in 1.2 herein. in addition, the manufacturer's pin may also be marked. for packages where marking of the entire smd pin number is not feasible due to space lim itations, the manufacturer has the option of not marking the "5962 - " on the device. 3.5.1 certification/compliance mark . a compliance indicator ?c? shall be marked on all non - jan devices built in compliance to mil - prf - 38535, appendix a. the compliance indicator ?c? shall be replaced with a "q" or "qml" certification mark in accordance with mil - prf - 38535 to identify when the qml flow option is used .
standard microcircuit drawing size a 5962- 86887 dla land and maritime columbus, ohio 43218 - 3990 revision level c sheet 4 dscc form 2234 apr 97 table i. electrical performance characteristics . test symbol conditions -55c t a +125 c v s = 15 v group a subgroups device type limits unit unless otherwise specified min max input offset voltage v io 1 01 80 v 2,3 180 input offset current i io 1 01 35 na 2,3 50 input bias current i ib 1 01 40 na 2,3 60 average input offset 1 / drift tc v io 1,2,3 01 1.0 v/ c power supply rejection ratio psrr v s = 4 v to 18 v 1 01 10 v/v 2,3 16 common mode rejection ratio cmrr v cm = 11 v 1 01 114 db v cm = 10 v 2,3 108 large signal voltage gain a vol v o = 10 v, r l 2 k ? 4 01 1000 v/mv 5,6 600 v o = 10 v, r l 600 ? 4 800 input voltage range ivr t a = +25 c 1 01 11.0 v t a = -55 c, +125 c 1 / 2,3 10.0 output voltage swing v op r l 2 k ? 4 01 12 v 5,6 11.5 r l 600 ? 4 10 slew rate sr r l 2 k ? , t a = +25 c 7 01 1.7 v/ s input noise voltage density e n f o = 10 hz, t a = +25 c 7 01 6.0 nv / f o = 1,000 hz, t a = +25 c 3.9 hz input noise current density i n f o = 10 hz, t a = +25 c 7 01 5.66 pa / f o = 1,000 hz, t a = +25 c 0.99 hz see footnotes at end of table.
standard microcircuit drawing size a 5962- 86887 dla land and maritime columbus, ohio 43218 - 3990 revision level c sheet 5 dscc form 2234 apr 97 table i. electrical performance characteristics ? continued. test symbol conditions -55c t a +125 c v s = 15 v group a subgroups device type limits unit unless otherwise specified min max gain bandwidth 1 / product gbw f = 100 khz, t a = +25 c 4 01 5.0 mhz power consumption p d each amplifier, t a = +25 c 1 01 140 mw input offset voltage match v os t a = +25 c 1 01 80 v t a = -55 c, +125 c 2,3 180 average noninverting bias current i b+ i b+ = ( i b+a + i b+b ) / 2, t a = +25 c 1 01 40 na i b+ = ( i b+a + i b+b ) / 2, t a = - 55 c, +125 c 2,3 60 noninverting offset current i os + i os + = ( i b+a - i b+b ), t a = +25 c 1 01 60 na i os + = ( i b+a - i b+b ), t a = -55 c, +125 c 2,3 90 inverting offset current i os - i os - = ( i b - a - i b - b ), t a = +25 c 1 01 60 na i os - = ( i b - a - i b - b ), t a = -55 c, +125 c 2,3 90 1 / guaranteed if not tested. 3.6 certificate of compliance . a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in mil - hdbk - 103 (see 6.6 herein). the certificate of compliance submitted to dla land and maritime - va prio r to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of mil - prf - 38535, appendix a and the requirements herein. 3.7 certificate of conformance . a certificate of conformance as required in mil -pr f - 38535, appendix a shall be provided with each lot of microcircuits delivered to this drawing. 3.8 notification of change . notification of change to dla land and maritime - va shall be required for any change that affects this drawing. 3.9 verificatio n and review . dla land and maritime, dla land and maritime 's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. offshore documentation shall be made available onshore at the o ption of the reviewer.
standard microcircuit drawing size a 5962- 86887 dla land and maritime columbus, ohio 43218 - 3990 revision level c sheet 6 dscc form 2234 apr 97 ( top view ) figure 1. terminal connections and logic diagram .
standard microcircuit drawing size a 5962- 86887 dla land and maritime columbus, ohio 43218 - 3990 revision level c sheet 7 dscc form 2234 apr 97 4. verification 4.1 sampling and inspection . sampling and inspection procedures shall be in accordance with mil - prf - 38535, appendix a. 4.2 screening . screening shall be in accordance with method 5004 of mil - std - 883, and shall be conducted on all devices prior to quality conformance inspection . the following additional criteria shall apply: a. burn - in test, method 1015 of mil- std -883. (1) test condition a, b, c, or d . the test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of mil - std -883. (2) t a = +125 c, minimum. b. interim and final electrical test parameters shall be as specified in table ii herein, except interim electrical parameter tests prior to burn - in are optional at the discretion of the manufacturer. table ii. electrical test requirements . mil - std -883 test requirements subgroups (in accordance with mil - std - 883, method 5005, table i) interim electrical parameters (method 5004) 1 final electrical test parameters (method 5004) 1*, 2,3,4 group a test requirements (method 5005) 1,2,3,4,5,6,7 groups c and d end - point electrical parameters (method 5005) 1,2,3 * pda applies to subgroup 1. 4.3 quality conformance inspection . quality conformance inspection shall be in accordance with method 5005 of mil - std - 883 including groups a, b, c, and d inspections. the following additional criteria shall apply. 4.3.1 group a inspection . a. tests shall be as specified in table ii herein. b. subgroups 8 , 9 , 10, and 11 in table i, method 5005 of mil - std - 883 shall be omitted.
standard microcircuit drawing size a 5962- 86887 dla land and maritime columbus, ohio 43218 - 3990 revision level sheet 8 dscc form 2234 apr 97 4.3.2 groups c and d inspections . a. end - point electrical parameters shall be as specified in table ii herein. b. steady - state life test conditions, method 1005 of mil- std - 883. (1) test condition a, b, c, or d . the test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of mil - std -883. (2) t a = +125 c, minimum. (3) test duration: 1,000 hours, except as permitted by method 1005 of mil - std -883. 5. packaging 5.1 packaging requirements . the requirements for packaging shall be in accordance with mil - prf - 38535, appendix a. 6. notes 6.1 intended use . microcircuits conforming to this drawing are intended for use for government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 replaceability . microcircuits covered by this drawing will repla ce the same generic device covered by a contractor - prepared specification or drawing. 6.3 configuration control of smd's . all proposed changes to existing smd's will be coordinated with the users of record for the individual documents. this coordinatio n will be accomplished using dd form 1692, engineering change proposal. 6.4 record of users . military and industrial users shall inform dla land and maritime when a system application requires configuration control and the applicable smd to that system . dla land and maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. users of drawings covering microelectronics devices (fsc 5962) should contact dla land and maritime - va, telep hone (614) 692 - 054 7 . 6.5 comments . comments on this drawing should be directed to dla land and maritime - va, columbus, ohio 43218 - 3990, or telephone (614) 692 - 0540 . 6.6 approved sources of supply . approved sources of supply are listed in mil - hdbk -103 . the vendors listed in mil- hdbk - 103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by dla land and maritime -va.
standard microcircuit drawing bulletin date: 10-10-25 approved sources of supply for smd 5962 -86887 are listed below for immediate acquisition information only and shall be added to mil - hdbk - 103 and qml- 38535 during the next revision. mil- hdbk - 103 and qml- 38535 will be revised to include the addition or deletion of sources. the vendors l isted below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by dla land and maritime - va. this information bulletin is superseded by the next dated revision of mil - hdbk - 103 and qml-38535. dla land and maritime maintains an online database of all current sources of supply at http://www.dscc.dla.mil/programs/smcr/ . standard microcircuit drawing pin 1 / vendor cage number vendor similar pin 2 / reference military specification pin 5962- 8688701ca 60264 mtlop - 227aqd m38510/13504bca 3 / op - 227aj/883b 3 / mp op - 227ay 3 / op - 227a883 5962- 8688701cc 3 / mtlop - 227aj/883 1 / the lead finish shown for each pin representing a hermetic package is the most readily available from the manufacturer listed for that part. if the desired lead finish is not listed contact the vendor to determine its availability. 2 / caution . do not use this number for item acquisition. items acquired to this number may not satisfy the performance requirements of this drawing. 3 / not available from an approved source of supply. vendor cage vendor name number and address 60264 minco technology labs, inc. 1805 rutherford lane austin, tx 78754 - 5101 the information contained herein is disseminated for convenience only and the government assumes no liability whatsoever for any inaccuracies in the information bulletin.
|
